Equation uncertainty adjustment of the gas flow measurement results with flowmeters with standard orifice plates
Ключові слова:
expansion factor, flow measurement, flowmeter, influence coefficient, mass flow rate, orificeplate, standard primary device, variable differential pressure method, uncertainty.Анотація
The analysis of the relative uncertainty of the measurement result equation of gas flowrate, using differential pressure flowmeters with standard orifice plates, defined in GOST 8.586.5-2005 and DSTU GOST 8.586.5:2009, is presented. It has been found out that this equation is presented in a simplified form by introducing simplified equations for calculation of relative influence coefficients of input variables upon mass gas flow rate and relative uncertainty of gas expansion factor. New analytical dependencies for estimation of relative coefficients of influence of differential pressure on orificeplate, of orificeplate hole diameter and measuring pipeline inner diameter on mass gas flow rate. The equation, used to calculate relative uncertainty of gas.expansion factor has been specified. The new equations, used to determine relative influence coefficients of absolute pressure and gas isentropic exponent coefficient on gas expansion factor have been obtained. It has been found out that relative influence coefficients of input variables on mass flow rate of gas and gas expansion factor accept lower values than coefficients of equations, given in Standards. Values of relative influence coefficients obtained from the authors' equations are in good agreement with the results of the calculation of the equations presented in differential form and given in ISO 5168:2005. The analytical dependence reduces relative uncertainty of gas flow rate measurement result.
Завантаження
Посилання
vytratomiriv zminnogo perepadu tysku, Institute for
energy audits and energy accounting, Lviv. (in
ukrainian)
[2] Standarts ISO 2008, Uncertainty of
measurement: part 3: guide to the expression of
uncertainty in measurement – 3rd edn, ISO/IEC Guide
98-3:2008, Switzerland.
[3] Zakharov, IP 2002, Teoria neopredelennosti v
izmereniiakh, Consum, Kharkiv. (in russian)
[4] Standarts ISO 2005, Measurement of fluid flow
– Evaluation of uncertainty, ISO 5168: 2005.
[5] Standarts ISO 2003, Measurement of fluid flow
by means of pressure differential devices inserted in
circular cross-section conduits running full: part 1:
general principles and requirements, ISO 5167-1:2003.
[6] Standarts ISO 2003, Measurement of fluid flow
by means of pressure differential devices inserted in
circular cross-section conduits running full: part 2:
orifice plates, ISO 5167-2:2003.
[7] Standarts ISO 2003, Measurement of fluid flow
by means of pressure differential devices inserted in
circular cross-section conduits running full: part 3:
Nozzles and Venturi nozzles, ISO 5167-3:2003.
[8] Standarts ISO 2003, Measurement of fluid flow
by means of pressure differential devices inserted in
circular cross-section conduits running full: part 4:
Venturi tubes, ISO 5167-4:2003.
[9] Standarts ISO 2003, Gosudarstvennaia sistema
obespecheniia edinstva izmerenii. Izmerenie raskhoda i
kolichestva zhidkostei i gazov s pomoshchiu
standartnykh suzhaiushchikh ustroistv: part 1: printsip
metoda izmerenii i obshchie trebovaniia, ISO 5167-
1:2003 : GOST 8.586.1:2005 [valid from 01.01.2007].
(in russian)
[10] Standarts ISO 2003, Gosudarstvennaia
sistema obespecheniia edinstva izmerenii. Izmerenie
raskhoda i kolichestva zhidkostei i gazov s pomoshchiu
standartnykh suzhaiushchikh ustroistv: part 2:
Diafragmy. Tekhnicheskie trebovaniia, ISO 5167-
2:2003 : GOST 8.586.2:2005 [valid from 01.01.2007].
(in russian)
[11] Standarts ISO 2003, Gosudarstvennaia
sistema obespecheniia edinstva izmerenii. Izmerenie
raskhoda i kolichestva zhidkostei i gazov s pomoshchiu
standartnykh suzhaiushchikh ustroistv: part 5: Metodika
vypolneniia izmerenii, ISO 5167 : GOST 8.586.5:2005
[valid from 01.01.2007]. (in russian)
[12] National standart of Ukraine 2010,
Metrologiia. Vymiriuvannia vytraty ta kilkosti ridyny i
gazu iz zastosuvanniam standartnykh zvuzhuvalnykh
prystroiv: part 1: pryntsyp metodu vymiriuvannia ta
zagalni vymogy, GOST 8.586.1–2005 (ISO 5167-
1:2003, IDT; ISO 5167-1:2003, NEQ) [Text] : DSTU
GOST 8.586.1:2009. [valid from 01.04.2010],
Derzhspozhyvstandart Ukrainy. (in ukrainian)
[13] National standart of Ukraine 2010,
Metrologiia. Vymiriuvannia vytraty ta kilkosti ridyny i
gazu iz zastosuvanniam standartnykh zvuzhuvalnykh
prystroiv: part 2: Diafragmy. Tekhnichni vymogy,
GOST 8.586.2–2005 (ISO 5167-2:2003, IDT; ISO
5167-2:2003, NEQ) [Text] : DSTU GOST
8.586.2:2009. [valid from 01.04.2010],
Derzhspozhyvstandart Ukrainy. (in ukrainian)
[14] National standart of Ukraine 2010,
Metrologiia. Vymiriuvannia vytraty ta kilkosti ridyny i
gazu iz zastosuvanniam standartnykh zvuzhuvalnykh
prystroiv: part 5: Metodyka vykonannia vymiriuvan,
GOST 8.586.5–2005 (ISO 5167-2:2003, IDT; ISO
5167-5:2003, NEQ) [Text] : DSTU GOST
8.586.5:2009. [valid from 01.04.2010],
Derzhspozhyvstandart Ukrainy. (in ukrainian)
[15] Pistun, EP 1973, Primenenie sredstv
vychislitelnoi tekhniki dlia povysheniia tochnosti
opedeleniia raskhoda, izmeriaemogo po metodu
peremennogo perepada davleniia, Lviv. (in russian)
##submission.downloads##
Опубліковано
Як цитувати
Номер
Розділ
Ліцензія
Авторське право